MARQ Haze 800 DMX | Water-based Hazer with Advanced Programming, Selectable Output & Wired Remote Control (800-watts)

0




Buy Now with Best Price



MARQ Lighting’s Haze 800 DMX delivers haze effects custom-tailored to your exact requirements.

DMX functions give you advanced programming options and complete control over every aspect of the unit’s performance. You can select from 1–100 percent fan speed or haze output and the included wired remote ensures simple operation.

Note: MARQ’s Haze Fluid Gallon and Haze Fluid Quart sold separately.

 

Frequently Asked Questions 

 

How do you set it up and know when the Haze 800 DMX is ready to use?

To get the Haze 800 DMX ready for use:

  1. First, fill the Haze 800 DMX to the required amount of fluid.  
     
  2. Next, on the remote control, set the Power Switch to the On position. The Power light will illuminate, and Haze 800 DMX will begin warming up.  

    Wait for 2–3 minutes for Haze 800 DMX to warm up. During this time, do not press any buttons on the remote control. The Ready light on the remote control will illuminate when it is ready to use.  
     
  3. When the Ready light on the remote control is on, turn the Output Volume knob to control the amount of haze.

 

Why is there no haze coming out?

This unit will pump out the haze only when the unit is heated up, and the light on the wired remote is illuminated.  If it has not had time to heat up, then it will not pump out fog.  When you plug in the Haze 800 DMX, it needs a few minutes to heat up to work.  Also, it is important to check the gauge on the back to make sure there is adequate amount of fluid.  

Never run the unit dry!


What type of haze fluid should I use?

We recommend using a high-quality, water-based haze fluid with Haze 800 DMX. You can purchase this from a local or online retailer. 

Important: Using non-water-based fluids with this product will void the warranty. 

 

How do you clean the Haze 800 DMX properly?

To clean the Haze 800 DMX, follow the steps suggested below:

  1. First, always unplug your Haze 800 DMX from the wall outlet.
     
  2. After each time you use Haze 800 DMX, turn the Output knob on the remote control completely counterclockwise, and then wait for 1–2 minutes.  Then, on the rear panel, press Function to cycle through the menu options until h and a number appear.  Use the Up/Down buttons to set it to 0 (off), and then wait for 1–2 minutes.  
     
  3. On your DMX controller, set the haze output (Channel 2) to 000, and then wait for 1–2 minutes. This will allow the heater to clear itself of any remaining fluid.

We also recommend wiping its metal housing with a soft, clean cloth.  You may also use compressed air and soft brush or a vacuum to remove dust from the external vents or internal parts.

Important: Do not clean Haze 800 DMX using solvents or harsh detergents. 

 

What does the remote control do?

The remote on the Haze 800 DMX controls the timing of the haze, the amount of haze you wish to send out and if you want to control manually or have it be automatic. 

  • To activate/deactivate the timer, press Timer On/Off on the remote control. When activated, the Timer light will illuminate and you can do the following
     
  • To set the amount of haze, turn the Output knob on the remote control. 
     
  • To set the amount of time of each release of haze, turn the Duration knob on the remote control. The available range is approximately 1–30 seconds. 
     
  • To set the amount of time between each release of haze, turn the Interval knob on the remote control. The available range is approximately 1–30 minutes.
    Note: It can take up to 30 seconds for the new values to take effect. 
     
  • To activate a continuous output of haze, do one of the following: Press Continuous to activate it. Press Continuous again to deactivate it. Press and hold Manual to activate it. Release Manual to deactivate it.

 

How do you use the DMX option?

The Haze 800 DMX has a DMX option so that you can control the fan speed and the haze output from a DMX controller.  Using a DMX controller can give you control from a more remote location if needed, so you are not constricted by the length of the built in remote.  It also allows you to control multiple hazers, fog machines or lights from one controller if that is what you want to do.  

Here is all you need to do to control via DMX:

  • Attach a controller to the DMX input on the Marq Haze DMX 800
  • Set the DMX address "channel" on Haze 800 DMX. To set the DMX address, press Function on the rear panel to cycle through the menu options until d and a number appears: 001 through 512. Use the Up/Down buttons to set the address. 
  • Now you can use a DMX controller to control the Haze 800 DMX.   

 

Further Technical Support

Whether you are a customer or dealer, if you already own a Marq product, or if you just have pre-sales questions, the Marq technical support team is available to help!

Visit the link below to connect with any of the following support options: online community support, phone support, email support.  

  • http://www.marqlighting.com/support 

 

Technical Specs

  • Haze Output: 2543 ft³/min
  • Tank Capacity: 40.5 fl oz
  • Fluid Consumption: 0.07 to 0.15 fluid ounces/min2
  • Heating Time: 2 minutes
  • Control: Microprocessor via wired remote control, 9.8-feet cable
  • Connections
    • (1) 3-pin input for DMX
    • (1) 3-pin output for DMX
    • (1) 5-pin remote control input
  • Power
    • Input Voltage: 120 VAC, 60 Hz 230 VAC, 50 Hz
    • Connection: Attached power cable
    • Consumption: 800 W, 6.6 A @ 120 V, 60 Hz 800 W, 3.4 A @ 230 V, 50 Hz
    • Fuse: 250 V, 8 A
  • Dimensions(width x depth x height): 12.2” x 7.2” x 10.9”
  • Net Weight: 14.6 lbs
  • Gross Weight: 16.3 lbs.

Box Contents

  • Haze 800 DMX
  • Remote Control (wired)
  • User Guide
  • Safety & Warranty Manual

800W hazer
800W hazer
Small footprint
800W hazer
800W hazer
Small footprint
Up to 4 hours run time on a single tank
800W hazer
800W hazer
Small footprint
800W hazer
800W hazer
Small footprint
Up to 4 hours run time on a single tank
DMX for advanced programing and variable control
800W hazer
800W hazer
Small footprint
800W hazer
800W hazer
Small footprint
Up to 4 hours run time on a single tank
800W hazer
800W hazer
Small footprint
800W hazer
800W hazer
Small footprint
Up to 4 hours run time on a single tank
DMX for advanced programing and variable control
Works with water-based haze fluids such as HazeFluidGal and HazeFluidQt from MARQ